Will Surge Protector Stop Breakers From Tripping?

The answer to the question: will a surge protector keep a breaker from tripping? If you use a low-power surge protector, it won’t stop the breakers from tripping That’s right. So only your appliance-compatible high-power surge protector can stop breakers from tripping!

Why does a low-power surge protector not stop breakers from tripping? Basically, breakers are designed to break a circuit in case a problem occurs. Surge protectors are designed to prevent or reduce the damage of power surges and/or low voltage. So surge protectors will not stop tripping if it’s not power compatible with your breaker.

To protect against power surges or low voltage for the house, a whole house surge protection device must be installed at the main service entrance. IT can stop power surges from entering your home.

When breakers trip, it means that the surges are too powerful or large for the device to handle. For this reason, you should avoid using more than one surge protector to protect your appliances.

You can read Why Is My Security Indicator Light Flashing?

Why a Circuit Breaker Trips?

A circuit breaker can trip for several reasons. When a circuit is overloaded with current, the breaker will trip in order to protect the wires and the electrical appliances you’re using. Below are the more matters that’s why a circuit breaker trips.

  • Circuit overload: The most common cause of a circuit breaker tripping is when there’s too much current running through the wires. If you’re using more appliances than the wiring can handle, the electricity will flow through the wires until it heats up the wire insulation to the point that it melts. The circuit breaker trips when this happens to prevent a fire.
  • Faulty wiring: A circuit breaker can also trip if there is faulty wiring somewhere in your house. For example, if the screw on your electrical outlet is not tightened all the way, it may cause a short. This will allow too much current to flow through your outlet and trip your breaker.
  • Grounding Problems: A ground fault interrupter (GFI) is an electrical outlet used to prevent shocks in the event that someone comes in contact with a “live” wire in your home. It’s essentially a circuit breaker built inside of the outlet and will trip if current runs through it when no appliances are turned on.
  • Short circuits: A short circuit happens when there is a direct connection between the “hot” wire and the “neutral” or “ground” wire. For example, if your toaster wire touches one of the metal prongs on your electrical outlet (while it’s still plugged in), this will cause a short circuit. This can be incredibly dangerous as it can lead to fires or electrocutions.

These are just some of the reasons why a circuit breaker trips, there are more reasons but these are the most common. There can be another cause that is not mentioned here, you may contact an electrician service to help you out with it.

Circuit Breaker

What to Do When Your Circuit Breaker Trips?

First, you should unplug all of the appliances plugged into the outlet when your circuit breaker trips. If one appliance trips the breaker, they all need to be turned off.

If an appliance trips your breaker and you can’t find anything, plug it into the outlet again. Then turn it on. If that doesn’t work, you’re going to have to plug the other appliances into different outlets. Whenever that happens again, there may be a problem with that appliance, so you should unplug it immediately.

When your circuit breaker trips often, an electrical or one of the above problems may exist in your home and should be addressed by a licensed electrician.

Tips to Avoid Breaker Tripping

Don’t overload a circuit:

Circuit breakers and fuses are rated according to their maximum load capacity. It is better to distribute your electrical load across several circuits to reduce the chance that one circuit will become overloaded and tripped. When all the outlets on a particular circuit are occupied, that is the maximum load that can be safely placed on it. Do not plug in another device if every outlet on the circuit is occupied.

Install GFCI Outlets:

A GFCI outlet can be used as a key part of the power distribution and protection system of your home. GFCI outlets protect against both electrocution and tripping circuits in the event of a ground fault by plugging in appliances and lighting. In this way, a ground fault will be detected and the circuit will trip, preventing a potentially dangerous situation.

Replace Old Electrical Components:

Although older homes may have many decades of life left in them. Therefore, it is generally not a smart idea to keep outdated components. Faulty wiring damaged electrical components, and obsolete electrical components can cause fires to begin. You can easily improve the safety of your home by replacing old outlets with GFCI receptacles.

Use the Right Appliances:

You should make sure you do not overload your circuits by using appliances that are greater than the capacity of the circuit. You must only plug a hot plate appliance into a circuit that’s designed for higher wattage appliances, such as your stove or dryer.

Use the Right Outlets:

Try to avoid plugging large appliances into small electrical outlets. This can cause an excessive amount of current to flow through a particular outlet, which can heat up and melt the insulation around the wires.

Use Ground Fault Circuit Interrupters:

It is a wise idea to use outlets that have a circuit breaker built into them, which will trip if there is a short in the wiring. People use them in bathrooms and kitchens, but you can add them to other areas of your home as well. So installing a ground fault circuit interrupter can stop tripping your breaker.

Turn Off Electronics:

Many electronics such as TVs, radios, and computers continue to consume electricity even when they’re turned off. This is often referred to as “phantom power”. It can add a great deal of unnecessary electricity to your monthly utility bills. When electronics aren’t in use, turning them can keep fuse breakers from tripping.

Unplug Electronics When Not in Use:

When your computer is plugged in even if it is off, it draws electricity. Unplug your computer or other electrical devices if you are not using them. In some cases, your circuit breaker may trip if you do not unplug your TV or electronic devices when they’re not being used.

Use an ideal surge protector/power strip:

Make sure your appliances are protected against power surges or fluctuations by using a surge protector. When not in use, some surge protectors have an energy saver/power management feature that cuts the power to certain appliances or electronics. So using a high-quality surge protector or power strip can stop breakers from tripping.

How to stop laser printer from tripping breaker?

Most laser printers have a fan located inside. If you are using your printer at work or in an office, you might have noticed that the fan is turned off when the printer is not in use. This saves energy and also prevents your laser printer from overheating during long periods of non-use.

If you are using your laser printer within the comfort of your home, you should use a well-rated surge protector. So that it will stop your laser printer from constantly tripping the surge protector’s circuit breaker during short periods of non-use.

FAQs

Is tv tripping the circuit breaker?

It’s a good question, so why is TV tripping your circuit breaker? Maybe the circuit can’t provide enough power for the TV. In other words, if you have a 42″ plasma television that requires 300 watts of electricity, it will require far more power than a computer, which only needs 15-20 watts. If everything is connected to one outlet strip, there will be a power outage, which will result in your circuit breaker tripping continuously.

Is hot weather tripping a breaker?

Yes, tripping a circuit breaker in hot weather is unpleasant for everyone, so how to stop it? The answer might be in the question. Try adding a new circuit to your house and have a licensed electrician install it. You can also try adding an outlet strip with a circuit breaker to each outlet in your house if this is not possible.
In addition, if the tripping only occurs when certain appliances are used, you may need to check their voltage requirements and see if their voltage supply is compatible with your home’s voltage supply.

Last Words

Finally, try to follow the above points to avoid tripping a circuit breaker. Also, using a high-power surge protector is the best way to protect your appliances and electronics from power surges and it will stop tripping breakers.

Besides, don’t use so many devices in a single power strip or surge protector, try to use separate outlet strips to connect with each device.

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.